install

  1. A

    I want to install some DiMarzio Titans in my guitar, but I need some advice.

    So, I have an HSH electric guitar that I'm modifying. I want to install some DiMarzio Titans in it, but there are two issues: 1. The guitar is HSH, and I need an additional pickup for the middle position. Is there anything you guys can suggest? And would ANY passive middle pickup be compatible...
  2. A

    Can I install a coil split switch with these pickups?

    Hi, everyone, I am currently modding/restoring a badly abused Ibanez RG170 with a 5-way selector switch. The following are photos of the bridge and neck pickups. I am thinking of adding a coil split switch to the neck and the bridge pickup. Keep in mind that I am relatively new to soldering...
  3. thrasher7

    Help selecting rg7420 bridge pickup

    Hey everyone, I am new here and have a couple questions. After 20 plus years of guitar playing I have finally bought a 7 string:hbang:. It's a 2013 Ibanez rg7420. I have a pickguard that deletes the neck p/u and am going to just have a volume and bridge p/u. My all time favorite pickup for many...
  4. Furyof

    Installing pickup for the first time..

    So I need some help I just bought my first pickup (lol if you have seen my other thread. And now I have this seemly monster task of installing it. I am studying the components right now but I just want general advice. I am changing just my bridge pickup. It is a Seymour Duncan pickup also. I...
  5. pettymusic

    Evertune Install

    Well, here we go. I eventually will get around to starting a full on build but first, I want to evertune my Ibanez 6 string. Then I want to build a neck for it. I have already cut a set of routing templates and practiced on a throw away body I had. I made a mistake in the measurements on one...
  6. M

    Not sure if I installed pups right...

    So I just "installed" my new Crunch Lab/Liquifire 7 combo in my Agile Interceptor 725. When soldering them, the wire between the volume and tone pots came loose. It looked like it was soldered to the back of the tone pot so I just heated up the solder and remade the connection. My guitar...
  7. neurosis

    EMG Hetlfield or Wylde in an SG Standard?

    Hi people :D I have been trying to sell a nice SG Standard from the 2010 GC exclusive run. Since it's not going to leave anytime soon cause all I get are offers for change, not cash, I am thinking of playing around with it and changing the pickups. I have had EMGs in a Les Paul before...
  8. ryan9896

    Kerry King EMG problem/question....????

    so i have installed the Kerry King EMG set w/ the boost switch in my jackson. i replaced my volume & tone pots, input jack, and all wires with the brand new pieces that came with the set, all brand new. i have successfully installed EMG 81/85's in this guitar previously and everything worked...
  9. R

    Plugins and Cubase help

    Hi guys, I've read the Cubase manual and searched this section of the forum and I couldn't find anything that helped in regards to my situation. I currently have Cubase 5 and for some reason Cubase isn't reading the additional plugins that I've installed. For example, I tried to install...
  10. SpaceDock

    NGD and NPD with Install!!! Ibanez S7 and Blackouts

    Alright guys, I got this done yesterday cuz it snowed over here so I didn't go to work. I have seen a lot of threads talking about the Phase 1 Blackouts, but I hadn't seen an install thread. Well here it is, my NGD might help some people instead of just being a showoff thread. First I have a...
  11. BlackMetalSins

    Need Help installing Blaze 7 Pickups In Rg7321

    I finally got my Blaze pickup set in. I un-soldered all my pickups out of my 7, went to put the Blaze 7 Bridge in, and the holes don't match. What should I do about this? Would it make a difference if the pickup isn't under the string like it would be with the stock pickups? Or do I need to fill...


Latest posts

Top